Speed Queen DR5000WE Installation Manual Page 1

Installation Instructionsfor DryersOriginal InstructionsKeep These Instructions for Future Reference.CAUTION: Read the instructions before using the m

Front View (Without Closet Door) DRY2663N_SVGBA A Side View (Closet Door) Front View (Closet Door) DRY2637N_SVGFF2 (G) 1. Closet Door2. Centered

Area DescriptionFree Standing/Alcove In-stallation Closet InstallationA* Dryer sides and rear clearance 0 in. [0 mm] 0 in. [0 mm]B Dryer top clearance

WARNINGTo reduce the risk of fire, DO NOT use plastic or thinfoil ducting to exhaust the dryer.W354WARNINGTo reduce the risk of fire, the exhaust duct

Number of 90° ElbowsWeather Hood TypeRecommended Use Only for Short Run InstallationsD673I_SVG111. 4 in. [102 mm]D802I_SVG11. 2.5 in. [64 mm]Maxim

1. Make certain your dryer is equipped for use with the type ofgas in your laundry room. Dryer is equipped at the factory forNatural Gas with a 3/8

For proper operation at altitudes above 3000 feet [915 m] the L.P.gas valve spud orifice size must be reduced to ensure completecombustion. Refer to T

NOTE: Use COPPER WIRE only.Shorter than 15 ft. (4.5 m) – use 10 AWGLonger than 15 ft. (4.5 m) – use 8 AWGD816I_SVGL1 L2 L1 L21516522348912131011761141

D695I_SVGFigure 73. Use a strain relief and insert end of power cord through powersupply hole.D696I_SVGFigure 84. Use the three screws from the ac

3. Remove earth/ground screw from earth/ground to neutral wireand save for use in Step 5. Earth/ground to neutral wire willbe attached to the neutra

The door on this dryer is completely reversible. To reverse doorproceed as follows:1. Remove four hinge attaching screws.D675I_SVGFigure 152. Remo

8. Using screwdriver, remove two door plugs, and reinstall onopposite side of door opening.D317S_SVGFigure 229. Reinstall four hinge attaching scr

The three-prong grounding plug on the power cord should beplugged directly into a polarized three-slot effectively groundedreceptacle rated 120 Volts

1. To view the burner flame, remove the lower front panel of thedryer.2. Close the loading door and start the dryer in a heat setting (re-fer to t

Installer ChecklistFast Track for Installing the Dryer1 Position and Level theDryer.DRY2634N_SVG6 Wipe Out Inside ofDryer.CHECK CHECK2 Connect Dryer E

WARNING WARNINGRisk of fire. Highly flammable material.W881Read all instructions before using unit.WARNINGFOR YOUR SAFETY, the information in this ma

The following information applies to the state of Massachusetts,USA.• This appliance can only be installed by a Massachusetts li-censed plumber or gas

Table of Contents...3Dimensions...

DimensionsElectric DryersA 22.38 in. [569 mm]B 8.0 in. [203 mm]C * 36 in. [914 mm]D (to controls) Electronic Control: *41.25 in. [1048 mm]Knob Control

Gas Dryers1. 3/8 in. N.P.T. Gas ConnectionA 22.38 in. [569 mm]B 8.0 in. [203 mm]C * 36 in. [914 mm]D Electronic Control: *41.25 in. [1048 mm]Knob Co

Installation Before You Start SuppliesFor most installations, the basic supplies you will need are:DRY2586N_SVG876543211. Wrench2. 1/4 inch Driver

1. Dryer Base2. Level3. Leveling LegFigure 2Installation© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 9 Part No. D51690